Видео


PC Case Made of Wood!



An amateur tries his hand (and almost chops it off) at building a PC case out of wood. Enjoy ;-)

Credits:
- Produced and presented by Celso Soares
- Music in the video by Celso Soares (That's me, the guy in the video :)
- Awesome animations for the intro and outro based on the work from the great Beeple. Check out his work here: http://beeple-crap.com/

A big thanks to my brother André for donating the PC parts for this experiment.


Просмотров: 17416
Добавлено:
Длительность: 8:21
Комментарии: 51

Тэги для этого Видео:



Найти больше видео в категории: "28"
Видео загрузил:
Показать больше видео, загруженных


Похожие видео:

Комментарии:

Автор Oliver Junge ( назад)
I really like the look of that case, it is absolutely beautiful.

A little tip if I may: next time use an sheet of aluminum for the front side. It can be cut by woodworking tools and you don't risk your limbs in what I have to say was the most avant-garde use of an circular saw I have ever seen. Also, aluminum is very easy to sand and file.

Автор Juzzike Olen ( назад)
it's ugly af

Автор wwklnd ( назад)
Neat project, charming is a very good descriptor of the end result! I'm building a more... professionally designed case myself and it's really interesting to see how people have gone about their work before me. Haven't watched your second video yet, but I really hope you sharpened your chisels for that one. ;)

Автор vooduu99 ( назад)
Very Ugly Pc Case....

Автор Fábio Tavares ( назад)
tuga ftw !

Автор Gilang Luqman ( назад)
aw.. that wood look so heavy.......
can I use smaller wood (thin)? I wanna make light case...

Автор Cédric LEBIS ( назад)
0_o Utiliser une scie circulaire avec une lame pour le bois, sur du métal !? Tu as de la chance qu'aucune dents de la lame se soit barré dans tes doigts ou autre... une simple scie à métaux manuel aurait suffis ^^ (moi un fraise de défonceuse m'a bien fait peur quand un morceau est partie littéralement transpercer une fenêtre...)
###########################################################################################
Désolé je l'ai fait en Français... J'ai pas le niveau pour faire tout le speech en Anglais ^^

Sinon pour utiliser un ciseau à bois (déjà, il doit être affûté, sinon tu n'arrivera à rien et pire, c'est plus dangereux q'un ciseau affûté) tu traces dans un premier temps les usinages.
Puis tu place le ciseau perpendiculaire à la planche, le plat le long de tes lignes, le tout à ~1;2 mm de cette ligne coté enlèvement de matière (car il va un peu reculer quand tu va frapper).
Puis tu frappes dessus, assez fort, mais pas trop (il ne doit pas se bloquer dedans ^^ ), tu répète le processus le long de toutes tes lignes de traçage (ça sert à couper les fibre du bois, pour éviter les arrachements).
Enfin tu peux commencer à évider ta zone sur 1~2 mm de profondeur (ciseau avec le biseau en bas). Puis tu répète l'ensemble du processus jusqu'à arriver à la bonne profondeur.
Après, ça, pour finir tu peux utiliser le tranchant de ton ciseau pour racler le fond de ton usinage, ça évitera un ponçage ;)
###########################################################################################
Sorry I did it in French ... I do not have the level to do all the speech in English ^^ (google translate)

Otherwise to use a chisel (already it must be sharpened, otherwise you will not get anything and worse, it is more dangerous than a sharp chisel) you first trace the machining.
Then you place the chisel perpendicular to the board, the flat along your lines, all to ~ 1; 2 mm of this line dimensioned removal of matter (because it goes back a little when you hit).
Then you hit it, strong enough, but not too much (it does not have to lock in ^ ^), you repeat the process along all your lines of tracing (it is used to cut the fibers of the wood, to avoid the pulls) .
Finally you can start to clear your area on 1 ~ 2 mm depth (chisel with bevel down). Then you repeat the whole process until reaching the right depth.
After that, to finish you can use the edge of your scissors to scrape the bottom of your machining, it will avoid sanding ;)

Автор Ismail Khayam ( назад)
Its not the best....for hot components the wood

Автор revilo314 ( назад)
This is much less good than most things.

Автор handel Bilal ( назад)
you are the best man

Автор Comic Blaster ( назад)
Before pc cases needed dust filters. Now termite filters probably need to be introduced as well

Автор Ray Utrup ( назад)
I like how that look it some like what I try to do as part of my HO train layout and you do some thing I de not thank of

Автор Good Enough Productions ( назад)
That looks quite nice, especially considering the tools you had on hand.

Автор Victor McDonald ( назад)
Looks like a really early switch based pc from like the 70's to early 80's. But it looks cool

Автор MY Dream PC UK ( назад)
some great ideas put into this project, motherboard tray and springs for hdd mounts
i might give it a go myself

Автор akram aslam ( назад)
I appreciate the effort. A great start and I have a feeling you'll build better cases in the times to come. I built a PC case out of thermocol once when I was 13 years old. It was indeed fun, so i can imagine you had quite a bit of fun!.. Keep em coming and good luck with your channel.

Автор AllNamesRntAvailable ( назад)
You ripped a capacitor and the gfx card still works? woah.

Автор Mon0x1de ( назад)
It was entertaining to watch.

Автор LightsAndDarks ( назад)
Wow very nice but i would get the dimentions of a small pc tower

Автор I Scare Sausages ( назад)
Hello Reddit!

Автор SenorMaxTheFantastic ( назад)
I wish you uploaded more. you have solid production quality and your vids have been quite interesting

Автор ali veli ( назад)
Good video man love your work

Автор osvldo ( назад)
Yay new vid !! Awesome

Вставка видео:

URL 
Ссылка 

Поиск Видео

Top Видео

Видео

Seo анализ сайта